---
title: "Sensor descriptions"
canonical: "https://docs.xirgoglobal.com/space/SD/27155348/Sensor+descriptions"
format: markdown
---
| ID | Name | Description |
| --- | --- | --- |
|  |  | Boolean sensors |
| 0 | - | - |
| 1 | SENSOR_MODEM_ON | Status of cell module on board |
| 2 | SENSOR_MOTION_DETECTED | Source: Accelerometer. Start: instantly. Reset: delayed |
| 3 | - | - |
| 4 | - | - |
| 5 | SENSOR_SYSTEM_TIME_PRESENT | Status to indicate whether system has a valid time |
| 6 | SENSOR_INSIDE_GEOZONE | Status to indicate whether device is currently inside geozone |
| 7 | SENSOR_POOR_GNSS_SIGNAL | Set when device has GNSS fix but Satellite count and HDOP is low |
| 8 | SENSOR_GSM_JAMMING | Status to indicate whether cellular connectivity is currently being jammed |
| 9 | SENSOR_ROAMING | Status to indicate whether cellular connectivity is currently in roaming mode |
| 10 | SENSOR_GSM_REGISTERED | Status to indicate device registration to cellular network |
| 11 | SENSOR_GPRS_REGISTERED | Status to indicate if GPRS service is currently available |
| 12 | SENSOR_PDP_ACTIVE | Status to indicate that device has currently active internet session (PDP) |
| 13 | SENSOR_PREFERRED_OPERATOR_ACTIVE | Status to indicate whether device is currently attached to preferred operator (only active if operator list is assigned in settings) |
| 14 | SENSOR_GNSS_SPEED_PRESENT | Status to indicate that speed value from GNSS receiver is above 0. |
| 15 | SENSOR_SIGNAL_WIEGAND_ID_PRESENT | Status to indicate that card ID value has been read using Wiegand26 protocol. 4 second reset delay after removing id |
| 16 | SENSOR_IN_2 | Status to indicate that IN2 has voltage above value configured through digital inputs threshold setting. |
| 17 | SENSOR_IN_3 | Status to indicate that IN3 has voltage above value configured through digital inputs threshold setting. |
| 18 | SENSOR_IN_4 | Status to indicate that IN4 has voltage above value configured through digital inputs threshold setting. |
| 19 | SENSOR_IN_5 | Status to indicate that IN5 has voltage above value configured through digital inputs threshold setting. |
| 20 | SENSOR_IN_7 | Status to indicate alternator voltage (virtual ignition) through power rail. 30 seconds to become 1 from 0. instantly from 0 to 1. threshold=13.2V |
| 21 | SENSOR_IN_8 | Status to indicate that selected ADC channel is above threshold set in the settings |
| 22 | SENSOR_ONE_HOUR_TICK | Set for 3 minutes every hour |
| 23 | SENSOR_SIX_HOURS_TICK | Set for 3 minutes every 6 hours |
| 24 | - | - |
| 25 | - | - |
| 26 | - | - |
| 27 | SENSOR_STATIC_SIGNAL_1 | Signal that persists it’s value even after software reset. Can be controlled with TCP and SMS commands over the air or using scripts to control device functions |
| 28 | SENSOR_STATIC_SIGNAL_2 | Signal that persists it’s value even after software reset. Can be controlled with TCP and SMS commands over the air or using scripts to control device functions |
| 29 | - | - |
| 30 | SENSOR_IBUTTON_PRESENT | Status to indicate when Ibutton tag has been read using 1 wire. 4 second reset delay after removing id |
| 31 | SENSOR_BOOL_USER_DEFINED_0 | Boolean type sensor to store custom values using scripts |
| 32 | SENSOR_BOOL_USER_DEFINED_1 | Boolean type sensor to store custom values using scripts |
| 33 | SENSOR_BOOL_USER_DEFINED_2 | Boolean type sensor to store custom values using scripts |
| 34 | SENSOR_BOOL_USER_DEFINED_3 | Boolean type sensor to store custom values using scripts |
| 35 | SENSOR_BOOL_USER_DEFINED_4 | Boolean type sensor to store custom values using scripts |
| 36 | SENSOR_BOOL_USER_DEFINED_5 | Boolean type sensor to store custom values using scripts |
| 37 | SENSOR_BOOL_USER_DEFINED_6 | Boolean type sensor to store custom values using scripts |
| 38 | SENSOR_BOOL_USER_DEFINED_7 | Boolean type sensor to store custom values using scripts |
| 39 | SENSOR_BOOL_USER_DEFINED_8 | Boolean type sensor to store custom values using scripts |
| 40 | SENSOR_BOOL_USER_DEFINED_9 | Boolean type sensor to store custom values using scripts |
| 41 | SENSOR_BOOL_USER_DEFINED_10 | Boolean type sensor to store custom values using scripts |
| 42 | SENSOR_BOOL_USER_DEFINED_11 | Boolean type sensor to store custom values using scripts |
| 43 | SENSOR_BOOL_USER_DEFINED_12 | Boolean type sensor to store custom values using scripts |
| 44 | SENSOR_BOOL_USER_DEFINED_13 | Boolean type sensor to store custom values using scripts |
| 45 | SENSOR_BOOL_USER_DEFINED_14 | Boolean type sensor to store custom values using scripts |
| 46 | SENSOR_BOOL_USER_DEFINED_15 | Boolean type sensor to store custom values using scripts |
| 47 | SENSOR_BOOL_USER_DEFINED_16 | Boolean type sensor to store custom values using scripts |
| 48 | SENSOR_BOOL_USER_DEFINED_17 | Boolean type sensor to store custom values using scripts |
| 49 | SENSOR_BOOL_USER_DEFINED_18 | Boolean type sensor to store custom values using scripts |
| 50 | SENSOR_BOOL_USER_DEFINED_19 | Boolean type sensor to store custom values using scripts |
| 51 | SENSOR_BOOL_USER_DEFINED_20 | Boolean type sensor to store custom values using scripts |
| 52 | SENSOR_BOOL_USER_DEFINED_21 | Boolean type sensor to store custom values using scripts |
| 53 | SENSOR_BOOL_USER_DEFINED_22 | Boolean type sensor to store custom values using scripts |
| 54 | SENSOR_BOOL_USER_DEFINED_23 | Boolean type sensor to store custom values using scripts |
| 55 | SENSOR_BOOL_USER_DEFINED_24 | Boolean type sensor to store custom values using scripts |
| 56 | SENSOR_BOOL_USER_DEFINED_25 | Boolean type sensor to store custom values using scripts |
| 57 | SENSOR_BOOL_USER_DEFINED_26 | Boolean type sensor to store custom values using scripts |
| 58 | SENSOR_BOOL_USER_DEFINED_27 | Boolean type sensor to store custom values using scripts |
| 59 | SENSOR_BOOL_USER_DEFINED_28 | Boolean type sensor to store custom values using scripts |
| 60 | SENSOR_BOOL_USER_DEFINED_29 | Boolean type sensor to store custom values using scripts |
| 61 | SENSOR_BOOL_USER_DEFINED_30 | Boolean type sensor to store custom values using scripts |
| 62 | SENSOR_BOOL_USER_DEFINED_31 | Boolean type sensor to store custom values using scripts |
| 63 | SENSOR_BOOL_USER_DEFINED_32 | Boolean type sensor to store custom values using scripts |
| 64 | SENSOR_BOOL_USER_DEFINED_33 | Boolean type sensor to store custom values using scripts |
| 65 | SENSOR_BOOL_USER_DEFINED_34 | Boolean type sensor to store custom values using scripts |
| 66 | SENSOR_BOOL_USER_DEFINED_35 | Boolean type sensor to store custom values using scripts |
| 67 | SENSOR_BOOL_USER_DEFINED_36 | Boolean type sensor to store custom values using scripts |
| 68 | SENSOR_BOOL_USER_DEFINED_37 | Boolean type sensor to store custom values using scripts |
| 69 | SENSOR_BOOL_USER_DEFINED_38 | Boolean type sensor to store custom values using scripts |
| 70 | SENSOR_BOOL_USER_DEFINED_39 | Boolean type sensor to store custom values using scripts |
| 71 | SENSOR_BOOL_USER_DEFINED_40 | Boolean type sensor to store custom values using scripts |
| 72 | SENSOR_BOOL_USER_DEFINED_41 | Boolean type sensor to store custom values using scripts |
| 73 | SENSOR_BOOL_USER_DEFINED_42 | Boolean type sensor to store custom values using scripts |
| 74 | SENSOR_BOOL_USER_DEFINED_43 | Boolean type sensor to store custom values using scripts |
| 75 | SENSOR_BOOL_USER_DEFINED_44 | Boolean type sensor to store custom values using scripts |
| 76 | SENSOR_BOOL_USER_DEFINED_45 | Boolean type sensor to store custom values using scripts |
| 77 | SENSOR_BOOL_USER_DEFINED_46 | Boolean type sensor to store custom values using scripts |
| 78 | SENSOR_BOOL_USER_DEFINED_47 | Boolean type sensor to store custom values using scripts |
| 79 | SENSOR_BOOL_USER_DEFINED_48 | Boolean type sensor to store custom values using scripts |
| 80 | SENSOR_BOOL_USER_DEFINED_49 | Boolean type sensor to store custom values using scripts |
| 81 | SENSOR_BOOL_USER_DEFINED_50 | Boolean type sensor to store custom values using scripts |
| 82 | SENSOR_BOOL_USER_DEFINED_51 | Boolean type sensor to store custom values using scripts |
| 83 | SENSOR_BOOL_USER_DEFINED_52 | Boolean type sensor to store custom values using scripts |
| 84 | SENSOR_BOOL_USER_DEFINED_53 | Boolean type sensor to store custom values using scripts |
| 85 | SENSOR_BOOL_USER_DEFINED_54 | Boolean type sensor to store custom values using scripts |
| 86 | SENSOR_BOOL_USER_DEFINED_55 | Boolean type sensor to store custom values using scripts |
| 87 | SENSOR_BOOL_USER_DEFINED_56 | Boolean type sensor to store custom values using scripts |
| 88 | SENSOR_BOOL_USER_DEFINED_57 | Boolean type sensor to store custom values using scripts |
| 89 | SENSOR_BOOL_USER_DEFINED_58 | Boolean type sensor to store custom values using scripts |
| 90 | SENSOR_BOOL_USER_DEFINED_59 | Boolean type sensor to store custom values using scripts |
| 91 | SENSOR_BOOL_USER_DEFINED_60 | Boolean type sensor to store custom values using scripts |
| 92 | SENSOR_BOOL_USER_DEFINED_61 | Boolean type sensor to store custom values using scripts |
| 93 | SENSOR_BOOL_USER_DEFINED_62 | Boolean type sensor to store custom values using scripts |
| 94 | SENSOR_BOOL_USER_DEFINED_63 | Boolean type sensor to store custom values using scripts |
| 95 | SENSOR_BOOL_USER_DEFINED_64 | Boolean type sensor to store custom values using scripts |
| 96 | SENSOR_ARMED | Signal from vehicle CAN bus to indicate alarm armed |
| 97 | SENSOR_LOCKED | Signal from vehicle CAN bus to indicate doors locked |
| 98 | SENSOR_DOORS_F_L | Signal from vehicle CAN bus to indicate front left doors open |
| 99 | SENSOR_DOORS_F_R | Signal from vehicle CAN bus to indicate front right doors open |
| 100 | SENSOR_DOORS_R_L | Signal from vehicle CAN bus to indicate rear left doors open |
| 101 | SENSOR_DOORS_R_R | Signal from vehicle CAN bus to indicate rear right doors open |
| 102 | SENSOR_BONNET | Signal from vehicle CAN bus to indicate bonnet open |
| 103 | SENSOR_TRUNK | Signal from vehicle CAN bus to indicate trunk open |
| 104 | - | - |
| 105 | - | - |
| 106 | - | - |
| 107 | - | - |
| 108 | SENSOR_FACTORY_ALARM | Signal from vehicle CAN bus to indicate factory alarm triggered |
| 109 | SENSOR_IGNITION | Signal from vehicle CAN bus to indicate ignition on |
| 110 | - | - |
| 111 | - | - |
| 112 | SENSOR_BOOL_USER_DEFINED_65 | Boolean type sensor to store custom values using scripts |
| 113 | SENSOR_BOOL_USER_DEFINED_66 | Boolean type sensor to store custom values using scripts |
| 114 | SENSOR_BOOL_USER_DEFINED_67 | Boolean type sensor to store custom values using scripts |
| 115 | SENSOR_BOOL_USER_DEFINED_68 | Boolean type sensor to store custom values using scripts |
| 116 | SENSOR_STOP_WARNING | Signal from vehicle CAN bus to indicate STOP warning lamp on |
| 117 | SENSOR_OIL_PRESSURE_WARNING | Signal from vehicle CAN bus to indicate oil pressure warning lamp on |
| 118 | SENSOR_COOLANT_FLUID_WARNING | Signal from vehicle CAN bus to indicate coolant fluid warning lamp on |
| 119 | SENSOR_BRAKE_SYSTEM_WARNING | Signal from vehicle CAN bus to indicate brake system warning lamp on |
| 120 | SENSOR_BATTERY_VOLTAGE_WARNING | Signal from vehicle CAN bus to indicate charging system warning lamp on |
| 121 | SENSOR_AIRBAG_WARNING | Signal from vehicle CAN bus to indicate airbag warning lamp on |
| 122 | SENSOR_CHECK_ENGINE_WARNING | Signal from vehicle CAN bus to indicate check engine warning lamp on |
| 123 | SENSOR_HEADLAMP_MALFUNCTION_WARNING | Signal from vehicle CAN bus to indicate headlamp malfunction warning lamp on |
| 124 | SENSOR_TIRE_PRESSURE_WARNING | Signal from vehicle CAN bus to indicate tire pressure warning lamp on |
| 125 | SENSOR_LOW_BRAKE_PAD_WARNING | Signal from vehicle CAN bus to indicate low brake pad warning lamp on |
| 126 | SENSOR_MASTER_WARNING | Signal from vehicle CAN bus to indicate master warning lamp on |
| 127 | SENSOR_ABS_WARNING | Signal from vehicle CAN bus to indicate ABS warning lamp on |
| 128 | SENSOR_LOW_FUEL_LEVEL_WARNING | Signal from vehicle CAN bus to indicate low fuel level warning lamp on |
| 129 | SENSOR_ESP_WARNING | Signal from vehicle CAN bus to indicate ESP warning lamp on |
| 130 | SENSOR_GLOW_PLUG_WARNING | Signal from vehicle CAN bus to indicate diesel fuel/air system warning lamp on |
| 131 | SENSOR_DPF_WARNING | Signal from vehicle CAN bus to indicate DPF warning lamp on |
| 132 | SENSOR_EPC_WARNING | Signal from vehicle CAN bus to indicate EPC warning lamp on |
| 133 | SENSOR_DRIVER_SEATBELT_WARNING | Signal from vehicle CAN bus to indicate driver seatbelt warning lamp on |
| 134 | SENSOR_PASSENGER_SEATBELT_WARNING | Signal from vehicle CAN bus to indicate passenger seatbelt warning lamp on |
| 135 | SENSOR_PARKING_LIGHT_INDICATOR | Signal from vehicle CAN bus to indicate parking light indicator on |
| 136 | SENSOR_HEADLIGHT_INDICATOR | Signal from vehicle CAN bus to indicate headlamp indicator on |
| 137 | SENSOR_HIGH_BEAM_LIGHT_INDICATOR | Signal from vehicle CAN bus to indicate high beam light indicator on |
| 138 | SENSOR_KEY_INSERTED | Signal from vehicle CAN bus to indicate key inserted |
| 139 | SENSOR_HANDBRAKE | Signal from vehicle CAN bus to indicate handbrake activated |
| 140 | SENSOR_FOOT_BRAKE | Signal from vehicle CAN bus to indicate footbrake pressed |
| 141 | SENSOR_ENGINE_WORKING | Signal from vehicle CAN bus to indicate engine on |
| 142 | SENSOR_READY_TO_DRIVE | Signal from vehicle CAN bus to indicate ready to drive lamp on |
| 143 | SENSOR_CRUISE_CONTROL | Signal from vehicle CAN bus to indicate cruise control on |
| 144 | SENSOR_RETARDER_AUTO | Signal from vehicle CAN bus to indicate retarder state - auto [Legacy] |
| 145 | SENSOR_RETARDER_MANUAL | Retarder state - manual [Legacy] |
| 146 | SENSOR_AIR_CONDITIONING | Signal from vehicle CAN bus to indicate air conditioning on |
| 147 | SENSOR_WEBASTO | Signal from vehicle CAN bus to indicate webasto on |
| 148 | SENSOR_OUT_1 | Returns status of OUT1 |
| 149 | SENSOR_OUT_2 | Returns status of OUT2 |
| 150 | SENSOR_OUT_3 | Returns status of OUT3 |
| 151 | SENSOR_OVERTURN | Source: Accelerometer. Start: instantly. Reset: delayed |
| 152 | SENSOR_SHOCK_1 | Source: Accelerometer. Start: instantly. Reset: delayed |
| 153 | SENSOR_SHOCK_2 | Source: Accelerometer. Start: instantly. Reset: delayed |
| 154 | SENSOR_OUT_4 | Returns status of OUT4 |
| 155 | SENSOR_GNSS_JAMMING | Signal to indicate GNSS jamming |
| 156 | SENSOR_TAMPER | Signal to indicate tamper button state (for devices equipped with tamper switch) |
| 157 | SENSOR_CLUTCH_PEDAL_PRESSED | Signal from vehicle CAN bus to indicate clutch pedal being pressed |
| 158 | SENSOR_PTO_ENABLED | Signal from vehicle CAN bus to indicate PTO enabled |
| 159 | SENSOR_CAN_ACTIVITY_PRESENT | CAN messages received during the last 10 seconds on CAN1 or on CAN2. |
| 160 | SENSOR_STATIC_SIGNAL_3 | Signal that persists it’s value even after software reset. Can be controlled with TCP and SMS commands over the air or using scripts to control device functions |
| 161 | SENSOR_STATIC_SIGNAL_4 | Signal that persists it’s value even after software reset. Can be controlled with TCP and SMS commands over the air or using scripts to control device functions |
| 162 | SENSOR_STATIC_SIGNAL_5 | Signal that persists it’s value even after software reset. Can be controlled with TCP and SMS commands over the air or using scripts to control device functions |
| 163 | - | - |
| 164 | - | - |
| 165 | - | - |
| 166 | - | - |
| 167 | SENSOR_EXTERNAL_POWER_PRESENT | Sensor to indicate that power is connected to device (voltage above 9V) |
| 168 | - | - |
| 169 | - | - |
| 170 | SENSOR_DTC_CAPTURED | - |
| 171 | SENSOR_CAN_1_ACTIVITY_PRESENT | CAN messages received during the last 10 seconds on CAN1 |
| 172 | SENSOR_CAN_2_ACTIVITY_PRESENT | CAN messages received during the last 10 seconds on CAN2. |
|  |  |  |
|  |  | Unsigned 8 bit sensors |
| 8192 | SENSOR_GNSS_SPEED | Speed received from GNSS in km/h |
| 8193 | SENSOR_GNSS_SATELLITES | Number of locked in satellites |
| 8194 | SENSOR_GNSS_H_DOP | - |
| 8195 | SENSOR_MOBILE_NETWORK_CODE | Mobile network code. Available once device is connected to cellular network. |
| 8196 | SENSOR_TIMING_ADVANCE | Timing Advance from GSM |
| 8197 | SENSOR_GSM_POWER | Cellular signal strength (RSSI) in dBm |
| 8198 | SENSOR_PEDAL_POSITION | Accelerator pedal position 1: 0 to 250 % op. range |
| 8199 | SENSOR_FUEL_LEVEL_1 | Fuel level in L or in %, 100=100% or 100L. Note: when using FMS: Fuel level 1: 0.4 %/bit, 0 offset, 0 to 250 % op. Range |
| 8200 | SENSOR_ENGINE_TEMPERATURE | Engine temperature |
| 8201 | SENSOR_FUEL_LEVEL_2 | Fuel level in L or in %, 100=100% or 100L. Note: when using FMS: Fuel level 2: 0.4 %/bit, 0 offset, 0 to 250 % op. range |
| 8202 | SENSOR_ENGINE_LOAD | Engine Load. Note: when using FMS: Engine percent load at current speed: 1 %/bit, 0 offset, 0 to 125 % op. range |
| 8203 | SENSOR_U8_USER_DEFINED_0 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8204 | SENSOR_U8_USER_DEFINED_1 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8205 | SENSOR_U8_USER_DEFINED_2 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8206 | SENSOR_U8_USER_DEFINED_3 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8207 | SENSOR_U8_USER_DEFINED_4 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8208 | SENSOR_U8_USER_DEFINED_5 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8209 | SENSOR_U8_USER_DEFINED_6 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8210 | SENSOR_U8_USER_DEFINED_7 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8211 | SENSOR_U8_USER_DEFINED_8 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8212 | SENSOR_U8_USER_DEFINED_9 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8213 | SENSOR_U8_USER_DEFINED_10 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8214 | SENSOR_U8_USER_DEFINED_11 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8215 | SENSOR_U8_USER_DEFINED_12 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8216 | SENSOR_U8_USER_DEFINED_13 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8217 | SENSOR_U8_USER_DEFINED_14 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8218 | SENSOR_U8_USER_DEFINED_15 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8219 | SENSOR_U8_USER_DEFINED_16 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8220 | SENSOR_U8_USER_DEFINED_17 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8221 | SENSOR_U8_USER_DEFINED_18 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8222 | SENSOR_U8_USER_DEFINED_19 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8223 | SENSOR_U8_USER_DEFINED_20 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8224 | SENSOR_U8_USER_DEFINED_21 | Unsigned 8 bits integer type sensor to store custom values using scripts |
| 8225 | SENSOR_ADBLUE_LEVEL | FMS Aftertreatment 1 Diesel Exhaust Fluid Tank 1 Level: 0 % = Empty, 100% = Full |
| 8226 | SENSOR_TOP_SPEED | Vehicle top speed |
| 8227 | SENSOR_GNSS_GMT_SECONDS | GMT seconds |
| 8228 | SENSOR_GNSS_GMT_MINUNTES | GMT minutes |
| 8229 | SENSOR_GNSS_GMT_HOURS | GMT hours |
| 8230 | SENSOR_GNSS_GMT_DAYS | GMT day |
| 8231 | SENSOR_GNSS_GMT_MONTHS | GMT month |
| 8232 | SENSOR_GNSS_GMT_YEARS | GMT year |
| 8233 | SENSOR_WAKE_UP_REASON | Wake up reason for script reload: 0 - Unknown, 1 - Motion, 2 - IN2, 3 - IN3, 4 - in4, 5 - IN5, 6 - RTC, 7 - Modem, 8 - CAN, 9 - Ext. Pow. Cut |
| 8234 | SENSOR_FUEL_LEVEL_TYPE | 0 - N/A, 1 - 1 %/bit, 2 - 0.4 %/bit, 3 - 1 L/bit |
| 8235 | SENSOR_DUMP_STATE | Can dump status: 0 - Idle, 1 - Waiting for Bitrate, 2 - Bitrate Found, 3 - Bitrate Not Found, 4 - Reading CAN bus, 5 - CAN Read Success, 6 - Can Read Failed. |
| 8236 | SENSOR_GEOZONE_ID | value is the last ID of geozone group that the device is currently in. |
| 8237 | SENSOR_SLOT_1_ACTIVITY | Binary encoded slot 1 activity from tachograph. 0b000 - break/rest, 0b001 - availability, 0b010 - work, 0b011 - driving, 0b100 - reserved, 0b101 reserved |
| 8238 | SENSOR_SLOT_2_ACTIVITY | Binary encoded slot 1 activity from tachograph. 0b000 - break/rest, 0b001 - availability, 0b010 - work, 0b011 - driving, 0b100 - reserved, 0b101 reserved |
| 8239 | SENSOR_TACHO_FILE_MANAGER_STATE | 0 - Tacho file manager at sleep state, communication inactive; 1 - Tacho file manager entering sleep state, communication ended; 2 - Tacho file manager card authentication in progress; 3 - Tacho file manager completed overview file collection and is uploading the file; 4 - Tacho file manager is requesting server to check commands for current vehicle number; 5 - Tacho file manager is requesting server to check commands for current 1st Driver Card; 6 - Tacho file manager is requesting server to check commands for current 2nd Driver Card; 7 - Tacho file manager is sending confirmation that overview file transfer completed; 8  - Tacho file manager is sending confirmation that 1st Driver Card file transfer completed; 9 - Tacho file manager is sending confirmation that 2nd Driver Card file transfer completed; 10 - Tacho connection failed, next attempt will be delayed. |
| 8240 | SENSOR_HARDWARE_TYPE | 255 - unknown, 55 - Light 2G, 56 - Light 3G, 70 - Light+ 2G, 71 Light+ 3G, 85 - StCAN 2G, 86 - StCAN 3G, 87 - StCAN 2G 32Mb, 100 - XtCAN 2G, 101 - XtCAN 3G, 102 - XtCAN 2G 32Mb, 115 - Tacho 2G, 116 - Tacho 3G, 117 - Tacho 2G 32Mb |
| 8241 | SENSOR_CRUISE_CONTROL_STATE | FMS, 0 - Off/Disabled, 1 – Hold, 2 – Accelerate, 3 – Decelerate, 4 – Resume, 5 – Set, 6 – Accel. Override, 7 - Not available |
| 8242 | SENSOR_BATTERY_TEMPERATURE_1 | - |
| 8243 | SENSOR_BATTERY_TEMPERATURE_2 | - |
| 8244 | SENSOR_BATTERY_TEMPERATURE_3 | - |
| 8245 | SENSOR_BATTERY_TEMPERATURE_4 | - |
| 8246 | SENSOR_WASHER_FLUID_LEVEL | Washer Fluid Level: 0 to 100 |
| 8247 | SENSOR_RETARDER_TORQUE_MODE | FMS. 0 means “No request”: retarder torque = 0 (no braking). Modes 1 to 14 indicate that there is either a torque request or the identified function is currently controlling the retarder: retarder torque may range from 0 (no braking) to the upper limit |
| 8248 | SENSOR_RETARDER_PERCENT_TORQUE | FMS Actual Retarder - Percent Torque |
| 8249 | SENSOR_RETARDER_SELECTION | FMS Retarder Selection, non-engine |
| 8250 | SENSOR_ENGINE_PERCENT_TORQUE | Actual Engine – Percent Torque: -125 to 125 % |
| 8251 | - | - |
| 8252 | SENSOR_CURRENT_GEAR | Transmission Current Gear: -125 to 125, negative values are reverse gears, positive values are forward gears, zero is neutral. 251 (0xFB) is park |
| 8253 | SENSOR_FRONT_WIPER_MODE | Front Operator Wiper Switch |
| 8254 | SENSOR_INTAKE_PRESSURE | Engine Intake Manifold #1 Absolute Pressure: 0 to 500 kPa |
| 8255 | SENSOR_OIL_PRESSURE | Engine Oil-Filter Outlet Pressure: 0 to 1000 kPa |
| 8256 | SENSOR_BAROMETRIC_PRESSURE | Barometric Pressure: 0 to 125 kPa |
| 8257 | SENSOR_BATTERY_CHARGE | - |
| 8258 | SENSOR_TRANSMISSION_OIL_LIFE | Transmission Oil Life Remaining: 0 to 100 % |
| 8259 | SENSOR_DPF_2_SOOT_LOAD | Diesel Particulate Filter 2 Soot Load Percent: 0 to 250 % |
| 8260 | SENSOR_DPF_1_SOOT_LOAD | Diesel Particulate Filter 1 Soot Load Percent: 0 to 250 % |
| 8261 | SENSOR_DPF_2_ASH_LOAD | Diesel Particulate Filter 2 Ash Load Percent: 0 to 250 % |
| 8262 | SENSOR_DPF_1_ASH_LOAD | Diesel Particulate Filter 1 Ash Load Percent: 0 to 250 % |
| 8263 | SENSOR_CLUTCH_LIFE_REMAINING | FMS Clutch life remaining: 0 to 100 % |
| 8264 | SENSOR_TRANSMISSION_SERVICE | Transmission Service Indicator: 0 - off, 1 - on continuously, 2 - flashing |
| 8265 | SENSOR_SERVICE_2_COMPONENT_ID | Identification of component needing service.  See Table SPN911_A. |
| 8266 | SENSOR_SERVICE_1_COMPONENT_ID_1 | Identification of component needing service.  See Table SPN911_A. |
| 8267 | SENSOR_SERVICE_1_COMPONENT_ID_2 | Identification of component needing service.  See Table SPN911_A. |
| 8268 | SENSOR_SERVICE_1_COMPONENT_ID_3 | Identification of component needing service.  See Table SPN911_A. |
| 8269 | SENSOR_HUMIDITY | Ambient air humidity: 0 to 100 % |
| 8270 | SENSOR_AUXILIARY_TANK_LEVEL | Auxiliary tank liquid level: 0 to 100 % |
| 8271 | SENSOR_MQTT_BROKER_STATUS | 0 - disconnected; 1 - connected |
| 8272 | SENSOR_SELF_ORIENTATION_STATUS | 0 - orientation lost, 1 - oriented |
| 8273 | SENSOR_PCB_VERSION | Hardware PCB version |
| 8274 | SENSOR_ASSEMBLY_VERSION | Hardware assembly version |
| 8275 | SENSOR_FUEL_LEVEL_PERCENT | Fuel level percent value |
|  |  |  |
|  |  | Unsigned 16 bit sensors |
| 12288 | SENSOR_VCC | Voltage measured on external power rail in mV |
| 12289 | SENSOR_ADC_5 | Voltage measured on ADC5 in mV |
| 12290 | SENSOR_ADC_4 | Voltage measured on ADC4 in mV |
| 12291 | SENSOR_ADC_3 | Voltage measured on ADC3 in mV |
| 12292 | SENSOR_VBAT | Voltage measured on internal battery rail in mV |
| 12293 | - | - |
| 12294 | - | - |
| 12295 | - | - |
| 12296 | SENSOR_MOBILE_COUNTRY_CODE | Mobile country code received from cellular network to which device is currently attached to |
| 12297 | SENSOR_LOCATION_AREA_CODE | GSM Location area code |
| 12298 | SENSOR_CELL_ID | ID of a cell to which cell module is currently attached to. |
| 12299 | SENSOR_GNSS_COURSE | 0 to 360, 0 when stationary |
| 12300 | SENSOR_ENGINE_SPEED | Sensor from vehicle CAN bus to indicate engine speed in RPM |
| 12301 | SENSOR_U16_USER_DEFINED_0 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12302 | SENSOR_U16_USER_DEFINED_1 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12303 | SENSOR_U16_USER_DEFINED_2 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12304 | SENSOR_U16_USER_DEFINED_3 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12305 | SENSOR_U16_USER_DEFINED_4 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12306 | SENSOR_U16_USER_DEFINED_5 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12307 | SENSOR_U16_USER_DEFINED_6 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12308 | SENSOR_U16_USER_DEFINED_7 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12309 | SENSOR_U16_USER_DEFINED_8 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12310 | SENSOR_U16_USER_DEFINED_9 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12311 | SENSOR_U16_USER_DEFINED_10 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12312 | SENSOR_U16_USER_DEFINED_11 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12313 | SENSOR_U16_USER_DEFINED_12 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12314 | SENSOR_U16_USER_DEFINED_13 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12315 | SENSOR_U16_USER_DEFINED_14 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12316 | SENSOR_U16_USER_DEFINED_15 | Unsigned 16 bits integer type sensor to store custom values using scripts |
| 12317 | SENSOR_WHEEL_SPEED | Wheel Speed from CAN bus |
| 12318 | SENSOR_FUEL_LEVEL_L | Fuel level volume from CAN bus |
| 12319 | - | - |
| 12320 | SENSOR_AGC_MONITOR | GNSS quality parameter (Automatic Gain Control) |
| 12321 | SENSOR_FUEL_RATE | FMS Fuel Rate:0 to 3,212.75 L/h |
| 12322 | SENSOR_FREQ_IN2 | Sensor to indicate frequency measured on IN2 input. |
| 12323 | SENSOR_FREQ_IN3 | Sensor to indicate frequency measured on IN3 input. |
| 12324 | SENSOR_FREQ_IN4 | Sensor to indicate frequency measured on IN4 input. |
| 12325 | SENSOR_FREQ_IN5 | Sensor to indicate frequency measured on IN5 input. |
| 12326 | SENSOR_PULSE_PERIOD_IN_2 | Average time between two pulses |
| 12327 | SENSOR_PULSE_PERIOD_IN_3 | Average time between two pulses |
| 12328 | SENSOR_PULSE_PERIOD_IN_4 | Average time between two pulses |
| 12329 | SENSOR_PULSE_PERIOD_IN_5 | Average time between two pulses |
| 12330 | SENSOR_AMBIENT_TEMPERATURE | Ambient Air Temperature |
| 12331 | SENSOR_CAN_1_COMMAND | Command Identifier used by canbase_b function on CAN1 |
| 12332 | SENSOR_CAN_2_COMMAND | Command Identifier used by canbase_b function on CAN2 |
| 12333 | SENSOR_AXLE_1_WEIGHT | Axle 1 weight |
| 12334 | SENSOR_AXLE_2_WEIGHT | Axle 2 weight |
| 12335 | SENSOR_AXLE_3_WEIGHT | Axle 3 weight |
| 12336 | SENSOR_AXLE_4_WEIGHT | Axle 4 weight |
| 12337 | SENSOR_AXLE_5_WEIGHT | Axle 5 weight |
| 12338 | SENSOR_TRAILER_WEIGHT | FMS Trailer Weight: 0 to 128,510 kg |
| 12339 | SENSOR_CARGO_AMBIENT_TEMPERATURE | FMS Cargo Ambient Temperature: -273 to 1735 °C |
| 12340 | SENSOR_INSTANT_FUEL_ECONOMY | FMS Instantaneous Fuel Economy: 0 to 125.5 km/L |
| 12341 | SENSOR_INTERIOR_TEMPERATURE | FMS Cab Interior Temperature: -273 to 1735 °C |
| 12342 | SENSOR_TRANSMISSION_TEMPERATURE | FMS Transmission Oil Temperature: -273 to 1735 °C |
| 12343 | SENSOR_CARGO_WEIGHT | FMS Cargo Weight: 0 to 128,510 kg |
| 12344 | SENSOR_SERVICE_DISTANCE | FMS Service Distance: -160635 to 160640 km |
| 12345 | SENSOR_GROSS_VEHICLE_WEIGHT | FMS Gross Combination Vehicle Weight: 0 to 642,550 kg |
| 12346 | SENSOR_RANGE | Remaining Distance with Current Fuel Level |
| 12347 | SENSOR_1979_RPM | J1979 Engine RPM: Min 0, Max 16383.75 rpm |
| 12348 | SENSOR_1979_MAF | J1979 MAF air flow rate: Min 0, Max 655.35 g/s |
| 12349 | SENSOR_1979_FUEL_RATE | J1979 Engine fuel rate: Min 0, Max 3212.75 L/h |
| 12350 | SENSOR_1979_RAIL_PRESSURE | J1979 Fuel Rail Pressure: Min 0, Max 5177.265 kPa |
| 12351 | SENSOR_SERVICE_DELAY_OP_TIME_BASED | FMS Service Delay/Operational Time Based: -32127 to 32128 km |
| 12352 | SENSOR_FREQ_IN_2_COUNT | Pulse count on IN2 |
| 12353 | SENSOR_FREQ_IN_3_COUNT | Pulse count on IN3 |
| 12354 | SENSOR_FREQ_IN_4_COUNT | Pulse count on IN4 |
| 12355 | SENSOR_FREQ_IN_5_COUNT | Pulse count on IN5 |
| 12356 | SENSOR_POWER_CUT_RESET | Count of power cut reset |
| 12357 | SENSOR_SOFTWARE_RESET | Count of software reset |
| 12358 | SENSOR_SELF_ORIENTATION_CONFIDENCE | Self orientation confidence, status sensor is set when confidence reaches 1200 |
| 12359 | SENSOR_TIME_TILL_SLEEP | Time until the device goes to sleep |
| 12360 | SENSOR_OW_HUMIDITY | Humidity from onewire sensor |
| 12361 | SENSOR_MAIN_FS_BYTES_PENDING | Data bytes left to send to telemetry server in Bytes |
| 12362 | SENSOR_EVENT_FS_BYTES_PENDING | Event data bytes left to send to telemetry server in Bytes |
|  |  |  |
|  |  | Unsigned 32 bit sensors |
| 16384 | SENSOR_SYSTEM_TIME | Unix time used for system services |
| 16385 | SENSOR_TOTAL_FUEL_USED | Total fuel used from CAN bus |
| 16386 | SENSOR_TOTAL_ENGINE_HOURS | FMS Total engine hours from CAN bus |
| 16387 | SENSOR_TOTAL_DISTANCE | Total distance from CAN bus |
| 16388 | - | - |
| 16389 | SENSOR_U32_USER_DEFINED_0 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16390 | SENSOR_U32_USER_DEFINED_1 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16391 | SENSOR_U32_USER_DEFINED_2 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16392 | SENSOR_U32_USER_DEFINED_3 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16393 | SENSOR_U32_USER_DEFINED_4 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16394 | SENSOR_U32_USER_DEFINED_5 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16395 | SENSOR_U32_USER_DEFINED_6 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16396 | SENSOR_U32_USER_DEFINED_7 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16397 | SENSOR_U32_USER_DEFINED_8 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16398 | SENSOR_U32_USER_DEFINED_9 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16399 | SENSOR_U32_USER_DEFINED_10 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16400 | SENSOR_U32_USER_DEFINED_11 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16401 | SENSOR_U32_USER_DEFINED_12 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16402 | SENSOR_U32_USER_DEFINED_13 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16403 | SENSOR_U32_USER_DEFINED_14 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16404 | SENSOR_U32_USER_DEFINED_15 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16405 | SENSOR_U32_USER_DEFINED_16 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16406 | SENSOR_U32_USER_DEFINED_17 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16407 | SENSOR_U32_USER_DEFINED_18 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16408 | SENSOR_U32_USER_DEFINED_19 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16409 | SENSOR_U32_USER_DEFINED_20 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16410 | SENSOR_U32_USER_DEFINED_21 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16411 | SENSOR_U32_USER_DEFINED_22 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16412 | SENSOR_U32_USER_DEFINED_23 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16413 | SENSOR_U32_USER_DEFINED_24 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16414 | SENSOR_U32_USER_DEFINED_25 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16415 | SENSOR_U32_USER_DEFINED_26 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16416 | SENSOR_U32_USER_DEFINED_27 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16417 | SENSOR_U32_USER_DEFINED_28 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16418 | SENSOR_U32_USER_DEFINED_29 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16419 | SENSOR_U32_USER_DEFINED_30 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16420 | SENSOR_U32_USER_DEFINED_31 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16421 | SENSOR_U32_USER_DEFINED_32 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16422 | SENSOR_U32_USER_DEFINED_33 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16423 | SENSOR_U32_USER_DEFINED_34 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16424 | SENSOR_U32_USER_DEFINED_35 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16425 | SENSOR_U32_USER_DEFINED_36 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16426 | SENSOR_U32_USER_DEFINED_37 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16427 | SENSOR_U32_USER_DEFINED_38 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16428 | SENSOR_U32_USER_DEFINED_39 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16429 | SENSOR_U32_USER_DEFINED_40 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16430 | SENSOR_U32_USER_DEFINED_41 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16431 | SENSOR_U32_USER_DEFINED_42 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16432 | SENSOR_U32_USER_DEFINED_43 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16433 | SENSOR_U32_USER_DEFINED_44 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16434 | SENSOR_U32_USER_DEFINED_45 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16435 | SENSOR_U32_USER_DEFINED_46 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16436 | SENSOR_U32_USER_DEFINED_47 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16437 | SENSOR_U32_USER_DEFINED_48 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16438 | SENSOR_U32_USER_DEFINED_49 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16439 | SENSOR_U32_USER_DEFINED_50 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16440 | SENSOR_U32_USER_DEFINED_51 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16441 | SENSOR_U32_USER_DEFINED_52 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16442 | SENSOR_U32_USER_DEFINED_53 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16443 | SENSOR_U32_USER_DEFINED_54 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16444 | SENSOR_U32_USER_DEFINED_55 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16445 | SENSOR_U32_USER_DEFINED_56 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16446 | SENSOR_U32_USER_DEFINED_57 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16447 | SENSOR_U32_USER_DEFINED_58 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16448 | SENSOR_U32_USER_DEFINED_59 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16449 | SENSOR_U32_USER_DEFINED_60 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16450 | SENSOR_U32_USER_DEFINED_61 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16451 | SENSOR_U32_USER_DEFINED_62 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16452 | SENSOR_U32_USER_DEFINED_63 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16453 | SENSOR_U32_USER_DEFINED_64 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16454 | SENSOR_U32_USER_DEFINED_65 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16455 | SENSOR_U32_USER_DEFINED_66 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16456 | SENSOR_U32_USER_DEFINED_67 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16457 | SENSOR_U32_USER_DEFINED_68 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16458 | SENSOR_U32_USER_DEFINED_69 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16459 | SENSOR_U32_USER_DEFINED_70 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16460 | SENSOR_U32_USER_DEFINED_71 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16461 | SENSOR_U32_USER_DEFINED_72 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16462 | SENSOR_U32_USER_DEFINED_73 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16463 | SENSOR_U32_USER_DEFINED_74 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16464 | SENSOR_U32_USER_DEFINED_75 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16465 | SENSOR_U32_USER_DEFINED_76 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16466 | SENSOR_U32_USER_DEFINED_77 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16467 | SENSOR_U32_USER_DEFINED_78 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16468 | SENSOR_U32_USER_DEFINED_79 | Unsigned 32 bits integer type sensor to store custom values using scripts |
| 16469 | SENSOR_TICKS_FROM_RESET | Internally calculated 1 s ticks from last reset |
| 16470 | SENSOR_RECEIVED_CAN | Counter of received messages from CAN bus |
| 16471 | SENSOR_MISSED_CAN | Counter of missed messages from CAN bus |
| 16472 | SENSOR_CAN_1_BIT_RATE | - |
| 16473 | SENSOR_CAN_2_BIT_RATE | - |
| 16474 | SENSOR_TOTAL_FUEL_USED_HIGH_RES | FMS High resolution engine total fuel used: 0 to 4211081.215 L |
| 16475 | SENSOR_TACHO_ODOMETER | Odometer from tachograph |
| 16476 | SENSOR_SLOT_1_TIME | Slot 1 time from tachograph |
| 16477 | SENSOR_SLOT_2_TIME | Slot 2 time from tachograph |
| 16478 | SENSOR_SLOT_1_DISTANCE | Slot 1 distance from tachograph |
| 16479 | SENSOR_SLOT_2_DISTANCE | Slot 2 distance from tachograph |
| 16480 | SENSOR_LAST_REGISTRATION_TIME | Timestamp of last successful data registration |
| 16481 | SENSOR_ID_WIEGAND_26 | Wiegand ID read using wiegand26 protocol |
| 16482 | SENSOR_TOTAL_DISTANCE_HIGH_RES | FMS High Resolution Vehicle Distance: 0 to 21055406 m |
| 16483 | SENSOR_AXLE_WEIGHT | FMS Axle Location [LS 8bits] and Axle Weight [MS 24bits]: 0 to 32127.5 kg |
| 16484 | SENSOR_TIME_OF_HARVESTING | - |
| 16485 | SENSOR_HARVESTED_AREA | - |
| 16486 | SENSOR_TACHOGRAPH_TIMESTAMP | - |
| 16487 | SENSOR_TICKS_FROM_RESET_MS | Internally calculated 1 ms ticks from last reset |
| 16488 | SENSOR_IDLE_TOTAL_FUEL_USED | Engine total idle fuel used: 0 to 2105540607.5 L |
| 16489 | SENSOR_IDLE_TOTAL_HOURS | Engine total idle hours: 0 to 0 to 210554060.75 h |
| 16490 | SENSOR_AXES_OVERFLOW_COUNTER | Accelerometer data buffer overflow counter |
| 16491 | SENSOR_NTP_TIME | Unix time reported by NTP server |
| 16492 | SENSOR_GNSS_TIME | Unix time reported by GNSS receiver |
| 16493 | SENSOR_SCRIPT_1_ID | Script identifier |
| 16494 | SENSOR_SCRIPT_2_ID | Script identifier |
| 16495 | SENSOR_SCRIPT_3_ID | Script identifier |
|  |  |  |
|  |  | Unsigned 64 bit sensors |
| 20480 | SENSOR_IBUTTON_ID | - |
| 20481 | SENSOR_U64_USER_DEFINED_0 | Unsigned 64 bits integer type sensor to store custom values using scripts |
| 20482 | SENSOR_U64_USER_DEFINED_1 | Unsigned 64 bits integer type sensor to store custom values using scripts |
| 20483 | SENSOR_U64_USER_DEFINED_2 | Unsigned 64 bits integer type sensor to store custom values using scripts |
| 20484 | SENSOR_TEMPERATURE_ID_1 | Temperature sensor ID from 1-wire |
| 20485 | SENSOR_TEMPERATURE_ID_2 | Temperature sensor ID from 1-wire |
| 20486 | SENSOR_TEMPERATURE_ID_3 | Temperature sensor ID from 1-wire |
| 20487 | SENSOR_TEMPERATURE_ID_4 | Temperature sensor ID from 1-wire |
| 20488 | SENSOR_TELL_TALE_STATUS_0 | FMS Tell Tale Status: FMS1. (Bit Field) |
| 20489 | SENSOR_TELL_TALE_STATUS_1 | FMS Tell Tale Status: FMS1. (Bit Field) |
| 20490 | SENSOR_TELL_TALE_STATUS_2 | FMS Tell Tale Status: FMS1. (Bit Field) |
| 20491 | SENSOR_TELL_TALE_STATUS_3 | FMS Tell Tale Status: FMS1. (Bit Field) |
| 20492 | SENSOR_TELL_TALE_STATUS_4 | FMS Tell Tale Status: FMS1. (Bit Field) |
| 20493 | SENSOR_TRAILER_ID | J1939 |
| 20494 | SENSOR_FMS_TACHOGRAPH | Tachograph : TCO1 in FMS Standard |
| 20495 | SENSOR_TIRE_CONDITION | J1939 |
|  |  |  |
|  |  | Signed 8 bit sensors |
| 24576 | SENSOR_S8_USER_DEFINED_0 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24577 | SENSOR_S8_USER_DEFINED_1 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24578 | SENSOR_S8_USER_DEFINED_2 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24579 | SENSOR_S8_USER_DEFINED_3 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24580 | SENSOR_S8_USER_DEFINED_4 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24581 | SENSOR_S8_USER_DEFINED_5 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24582 | SENSOR_S8_USER_DEFINED_6 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24583 | SENSOR_S8_USER_DEFINED_7 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24584 | SENSOR_S8_USER_DEFINED_8 | Signed 8 bits integer type sensor to store custom values using scripts |
| 24585 | SENSOR_S8_USER_DEFINED_9 | Signed 8 bits integer type sensor to store custom values using scripts |
|  |  |  |
|  |  | Signed 16 bit sensors |
| 28672 | SENSOR_AXES_X | 1/4096 multiplier |
| 28673 | SENSOR_AXES_Y | 1/4096 multiplier |
| 28674 | SENSOR_AXES_Z | 1/4096 multiplier |
| 28675 | SENSOR_ALTITUDE | Altitude value in meters above sea level received from GNSS |
| 28676 | SENSOR_S16_USER_DEFINED_0 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28677 | SENSOR_S16_USER_DEFINED_1 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28678 | SENSOR_S16_USER_DEFINED_2 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28679 | SENSOR_S16_USER_DEFINED_3 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28680 | SENSOR_S16_USER_DEFINED_4 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28681 | SENSOR_S16_USER_DEFINED_5 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28682 | SENSOR_S16_USER_DEFINED_6 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28683 | SENSOR_S16_USER_DEFINED_7 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28684 | SENSOR_S16_USER_DEFINED_8 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28685 | SENSOR_S16_USER_DEFINED_9 | Signed 16 bits integer type sensor to store custom values using scripts |
| 28686 | SENSOR_CELLULAR_TEMPERATURE | Temperature read from cell module in degrees (C) |
| 28687 | SENSOR_LOCAL_TIME_ZONE | Local time zone, expressed in quarters of an hour. Range: -48 to +56 |
|  |  |  |
|  |  | Signed 32 bit sensors |
| 32768 | SENSOR_S32_USER_DEFINED_0 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32769 | SENSOR_S32_USER_DEFINED_1 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32770 | SENSOR_S32_USER_DEFINED_2 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32771 | SENSOR_S32_USER_DEFINED_3 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32772 | SENSOR_S32_USER_DEFINED_4 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32773 | SENSOR_S32_USER_DEFINED_5 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32774 | SENSOR_S32_USER_DEFINED_6 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32775 | SENSOR_S32_USER_DEFINED_7 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32776 | SENSOR_S32_USER_DEFINED_8 | Signed 32 bits integer type sensor to store custom values using scripts |
| 32777 | SENSOR_S32_USER_DEFINED_9 | Signed 32 bits integer type sensor to store custom values using scripts |
|  |  |  |
|  |  | Floating point 32 bit sensors |
| 40960 | SENSOR_TEMPERATURE | Temperature from 1-wire sensor, 60 s delay after failure |
| 40961 | SENSOR_ACCELERATION | positive values for acceleration, negative for braking |
| 40962 | SENSOR_CORNERING | positive values when turning one direction, negative - other direction |
| 40963 | SENSOR_F32_USER_DEFINED_0 | Floating point (32bit) type sensor to store custom values using scripts |
| 40964 | SENSOR_F32_USER_DEFINED_1 | Floating point (32bit) type sensor to store custom values using scripts |
| 40965 | SENSOR_F32_USER_DEFINED_2 | Floating point (32bit) type sensor to store custom values using scripts |
| 40966 | SENSOR_F32_USER_DEFINED_3 | Floating point (32bit) type sensor to store custom values using scripts |
| 40967 | SENSOR_F32_USER_DEFINED_4 | Floating point (32bit) type sensor to store custom values using scripts |
| 40968 | SENSOR_F32_USER_DEFINED_5 | Floating point (32bit) type sensor to store custom values using scripts |
| 40969 | SENSOR_F32_USER_DEFINED_6 | Floating point (32bit) type sensor to store custom values using scripts |
| 40970 | SENSOR_F32_USER_DEFINED_7 | Floating point (32bit) type sensor to store custom values using scripts |
| 40971 | SENSOR_F32_USER_DEFINED_8 | Floating point (32bit) type sensor to store custom values using scripts |
| 40972 | SENSOR_F32_USER_DEFINED_9 | Floating point (32bit) type sensor to store custom values using scripts |
| 40973 | SENSOR_F32_USER_DEFINED_10 | Floating point (32bit) type sensor to store custom values using scripts |
| 40974 | SENSOR_F32_USER_DEFINED_11 | Floating point (32bit) type sensor to store custom values using scripts |
| 40975 | SENSOR_F32_USER_DEFINED_12 | Floating point (32bit) type sensor to store custom values using scripts |
| 40976 | SENSOR_F32_USER_DEFINED_13 | Floating point (32bit) type sensor to store custom values using scripts |
| 40977 | SENSOR_F32_USER_DEFINED_14 | Floating point (32bit) type sensor to store custom values using scripts |
| 40978 | SENSOR_F32_USER_DEFINED_15 | Floating point (32bit) type sensor to store custom values using scripts |
| 40979 | SENSOR_F32_USER_DEFINED_16 | Floating point (32bit) type sensor to store custom values using scripts |
| 40980 | SENSOR_F32_USER_DEFINED_17 | Floating point (32bit) type sensor to store custom values using scripts |
| 40981 | SENSOR_F32_USER_DEFINED_18 | Floating point (32bit) type sensor to store custom values using scripts |
| 40982 | SENSOR_F32_USER_DEFINED_19 | Floating point (32bit) type sensor to store custom values using scripts |
| 40983 | SENSOR_TEMPERATURE_1 | Temperature from 1-wire sensor |
| 40984 | SENSOR_TEMPERATURE_2 | Temperature from 1-wire sensor |
| 40985 | SENSOR_TEMPERATURE_3 | Temperature from 1-wire sensor |
| 40986 | SENSOR_TEMPERATURE_4 | Temperature from 1-wire sensor |
| 40987 | SENSOR_FUEL_INSTANT | Fuel instant consumption form CAN bus |
| 40988 | SENSOR_BOARD_TEMPERATURE | Temperature measured on devices board ie thermistor or discrete temperature sensor |
|  |  |  |
|  |  | Double precision floating point 64 bit sensors |
| 45056 | SENSOR_GNSS_LONGITUDE | - |
| 45057 | SENSOR_GNSS_LATITUDE | - |
| 45058 | SENSOR_DISTANCE | Odometer from GNSS |
|  |  |  |
|  |  | String sensors |
| 49152 | SENSOR_STRING_1 | Max string size - 254 |
| 49153 | SENSOR_STRING_2 | Max string size - 254 |
| 49154 | SENSOR_STRING_3 | Max string size - 254 |
| 49155 | SENSOR_STRING_4 | Max string size - 254 |
| 49156 | SENSOR_SCRIPT_1_NAME | - |
| 49157 | SENSOR_SCRIPT_2_NAME | - |
| 49158 | SENSOR_SCRIPT_3_NAME | - |
| 49159 | SENSOR_IMEI | Cell module IMEI. Value becomes available right after first cell module boot after software reset. |
| 49160 | SENSOR_APN_NAME | Currently used APN name |
| 49161 | SENSOR_APN_USER | Currently used APN user |
| 49162 | SENSOR_APN_PASSWORD | Currently used APN password |
| 49163 | SENSOR_PREFERED_IP | - |
| 49164 | SENSOR_SERVER_1_NAME | - |
| 49165 | SENSOR_SERVER_2_NAME | - |
| 49166 | SENSOR_SOCKET_TYPE | - |
| 49167 | SENSOR_SERVER_SMS_NUMBER | - |
| 49168 | SENSOR_DEBUG_SMS_NUMBER | - |
| 49169 | SENSOR_ALARM_SMS_NUMBER | - |
| 49170 | SENSOR_FIRMWARE_VERSION | - |
| 49171 | SENSOR_IMSI | SIM card IMSI number. Value becomes available right after first cell module boot when SIM card is present. |
| 49172 | SENSOR_ICCID | SIM card ICCID. Value becomes available right after first cell module boot when SIM card is present. |
| 49173 | SENSOR_DTC | FMS Diagnostic trouble codes. Buffer is filled during telemetry packet generation |
| 49174 | SENSOR_DRIVER_1_ID | Card ID inserted into 1st tachograph slot |
| 49175 | SENSOR_DRIVER_2_ID | Card ID inserted into 2nd tachograph slot |
| 49176 | SENSOR_ISOBUS_NAME | ISOBUS implement NAME as described in EN11783-5 |
| 49177 | SENSOR_NETWORK_INFO | This sensor indicates network information such as the access technology selected, the operator, and the band selected. |
| 49178 | SENSOR_MODEM_FIRMWARE_VERSION | - |
| 49179 | SENSOR_VIN_D8 | - |
| 49180 | SENSOR_DTCO_VERSION | - |
| 49181 | SENSOR_VIN_PLATE_CAN | - |
| 49182 | SENSOR_BT_FIRMWARE_VERSION | - |
|  |  |  |
|  |  |  |
| 53248 | SENSOR_GNSS_COORDINATES | 16 bytes of data in following order: Latitude (float), Longitude (float), Speed (16 bits unsigned), HDOP (8 bits unsigned, value has to be divided by 10), Satellites (8 bits unsigned), Course (16 bits unsigned), Altitude (16 bits signed) |
|  |  |  |
|  |  | Custom structures |
| 61431 | - | - |
| 61432 | SENSOR_ISOBUS_IMPLEMENT_1 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61433 | SENSOR_ISOBUS_IMPLEMENT_2 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61434 | SENSOR_ISOBUS_IMPLEMENT_3 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61435 | SENSOR_ISOBUS_IMPLEMENT_4 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61436 | SENSOR_ISOBUS_IMPLEMENT_5 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61437 | SENSOR_ISOBUS_IMPLEMENT_6 | BCE_IOTM protocol. Annex B. Specific structure parsing for ISOBUS messages |
| 61438 | SENSOR_ISOBUS_IMPLEMENT | Legacy, not used |
|  |  |  |